If you’ve decided to enter the Bulk Cat6 Cables installation market, it’s vital that you make sure you do your job right. A big part of being able to charge customers a premium price in the industry is delivering high-quality service. It is something that requires more than just years of experience. You need to know how to install the Cat6 cable 1000ft properly if you want to keep your customers happy. And make sure that their networks stay up and running without any issues. Keep reading this Bulk Cat6 Cables Installation Guide for Independent Installers to learn more.
Installing Cat6 Cable 1000ft
In this step-by-step guide, you will learn everything you need to know about installing bulk cat6 cables. As an independent installer, you may be wondering how to install Cat6 plenum 1000ft cables. The short answer is that you install it just like you would install a Riser-rated cable. Or any other in the same category.
Tools and Materials Needed
Before you begin the Cat6 plenum installation, you will need to prepare all the materials and tools required. The best practice is to make a list of everything you will need and work in a systematic manner to keep your productivity at its peak.
You will need the following materials and tools for a flawless and highly functional Cat6 ethernet plenum cable installation.
Cat6 cable 1000ft, crimp connectors, RJ45 connectors, punch down tool, wire strippers/cutters.
To reiterate, assemble your tools and materials in advance of your installation so you don't have to spend time doing it on the job site. This will not only save you time but will make the process more efficient.
Preparing the Area
Before starting the installation, it is important to prepare the area by first removing any old cables and properly labeling them. If a cable is already labeled, make sure not to cover or obscure the labels.
It is also important that the area be free from debris and clutter so that installation can be done as quickly and efficiently as possible.
At this stage, you should also anticipate any hurdles you may have to face later. And it is best to make a blueprint of the network. Meaning, you should decide in advance where each cable will go and how much. Also, note the number of keystone jacks that you are going to connect.
Laying the Cat6 Plenum Cable
The first thing you'll need to do is connect the server’s end of the cable. The other end of the cable will be connected after you have pulled it through the walls and ducts.
Cat6 cables feature 4 pairs of twisted copper wires inside which are terminated into the 8P8C connectors, also known as RJ45. It's important not to cut the wires too short because they may not reach the jack or plug on the other end.
Once the server’s end of the cable has been terminated, you will need to pull the other end of the cable through its designated duct, wall, or plenum. There are many tools that can assist you to carry out this process. And as an independent network cable installer, it's best to use as many automation tools as possible.
Connecting the Cable
Once the cable has been pulled into, it is time to connect the other end with a keystone jack. Know that the keystone jack will be fixed to a faceplate in which patch panels will be connected directly to devices.
This can be done by using a punch-down tool or a crimp-on connector. To connect with a punch-down tool, first, strip off about 1/2 inch of sheathing from the end of the wire and then cut back about 1/2 inch from one side of the core wire so you have some space in between. Insert your wire into the hole where it will be held securely in place while being punched down. Make sure that you have lined up your wire so that it is straight and facing in the right direction.
To ensure a proper connection has been made, use a crossover tester on each end of the cable. The tester will light up green if the connector has been connected correctly. If not, it will light up red, indicating an incorrect termination.
Testing the Connection
Testing the connections or links, as we say, is very important. Perhaps, the most important part of the entire process. It is at this moment that you will know how good or bad you have installed the Cat6 plenum cable.
To test your connection, you can use a cable tester that you should have purchased when you bought the bulk Cat6 cable. Plug the tester into one end of the cable and plug the other end of the cable into your computer’s Ethernet port or WAN port on your router. If the cable is good, then it will show as connected. If there is a problem with your installation, it will tell you which wire is faulty.
You can also test by plugging one end of a network switch or hub into an Ethernet port on your PC and then plugging another computer in at each of its ports. The switch or hub should be set as off before testing so that no data is transferred over any connections while testing them.
Summary of the Bulk Cat6 Cable Installation Procedure:
- Prepare the cables, tools, ducts, and other spaces where cables will be run.
- Pull the cables and terminate the jacks.
- Test each connection with a networking cable tester.
Conclusion
This was a step-by-step installation guide on how to install bulk cat6 cables as an independent network cable installer. You can also take help from it to install other 1000ft ethernet cables. The process starts with preparing all the tools and materials needed and ends with terminating the cables into keystone jacks and then testing them. Feel free to share this article if it was helpful.
